Ponte posteriore Dana 70 Jeep Wrangler JK 07-18

 12.485,00 IVA inclusa

* Le immagini potrebbero non corrsipondere al prodotto reale.

Assali completi Currie Enterprises .
Il ponte posteriore Dana 70 Jeep Wrangler JK
è il top di gamma Currie per la vostra JK!

INFO PRODOTTO:

– L’installazione richiede la sostituzione dell’albero di trasmissione
– Dana 70 High Pinion con struttura centrale rinforzata

Esaurito


Ponte posteriore Currie Dana 70 Jeep Wrangler JK

– Facile installazione

– High Pinion con struttura centrale rinforzata

– Verniciatura speciale anti-corrosione

– Full floating

Il Ponte posteriore Currie Dana 70 per Jeep Wrangler JK 07-18 rappresenta il top di gamma Currie,  è  stato progettato per supportare pneumatici maggiorati fino alle 40″ e resistere alle prove off-road più dure al mondo.

Ponte anteriore Dana 70 Jeep Wrangler JK

Ponte anteriore Dana 70 Jeep Wrangler JK

 

SCHEDA TECNICA:

Vehicle FitmentCurrie 70 high-pinion nodular iron radius bottom center section
Bearing CapsIncreased cross section nodular iron caps secured with ARP® fasteners
Pinion BearingLarge diameter front pinion bearing matched to rear bearing
Pinion OilingHigh volume flow-thru recirculating oil system
Gear SetCurrie competition-grade 9310 gear set with 35-spline pinion, custom heat treated for strength and durability
Differential Carrier70 series high speed differential carrier (designed for low numerical gears) are used, enabling the use of stronger thick ring gears for all gear ratios
Ring Gear Load BoltEliminates ring gear deflection under heavy load (3/4″-16 right hand thread with Jam nut)
Pinion Yoke1350 u-joint
Skid PlateAR400 hardened steel skid plate
Differential CoverCurrie nodular-iron cover with gasketed fill plug with dipstick, Red
Axle Tubes3.5 inch diameter. .375 wall DOM tubing
AxlesCurrie Performance full-floating 40-spline (1.7” diameter) 4340 heat treated chromoly
Floater SpindleCurrie Performance 2.5″ 4140 Chromoly spindle, supports 35 or 40-spline axles
Floater HubCurrie Performance hubs with 40-spline drive flanges, JK tone rings installed for ABS and ESP retention
Brake Rotors12″ vented rotors with zinc plated caliper brackets
Brake CalipersOEM fitment JK rear calipers
Suspension BracketsHeavy gauge 3/16” steel mounting brackets with multiple mounting locations that enable the suspension geometry to be tuned
GeometryOptimized for 4” lift kits with 5 degrees of pinion angle to reduce driveshaft angle
Width70” wide (between wheel mounting surfaces), enables increased clearance for 37 inch and larger tires
Wheel Bolt PatternOptions include 5 on 5 1/2 or 6 on 5 1/2 with 1/2 inch studs or 8 on 6.5 with 9/16 studs
FinishBlack satin powder coat

 

Ponte posteriore Dana 70 Jeep Wrangler JK

TORNA SU
Chat
Need Help / Hai bisogno di Aiuto ?
Benvenuto nel supporto clienti
Acerni Custom Engineerign

♠️ I nostri Orari:
Dal Lunedì al Venerdì:
08:00-12:30 / 14:00-19:00
Sabato: 08:00-12:30